slippage

n.滑动；下跌；滑动量；下跌量

noun

1. 延误；逾期
   failure to achieve an aim or complete a task by a particular date
2. （微弱或逐渐的）下降，降低，贬值
   a slight or gradual fall in the amount, value, etc. of sth

名词复数形式:slippages

1. We want to stop the slippage of the quality of public services.
   我们想要止住公共服务质量下滑的局面。
2. Surface Free Energy and Solid-Liquid Slippage.
   界面自由能与滑移。
3. Variations in rock type and structure in the fault zone would entail variations in slippage rate along the trace.
   断层区的岩石类型和构造的不同将会引起沿断痕滑动的速率的变化。
4. One mode is slippage along the discontinuity provided by the lubricated fault plane.
   其中一种方式是沿着润滑的断层面所形成的间断面而发生滑动。
5. These forces may cause fiber slippage within the yarn structure.
   这些力会引起纱线结构内部纤维的滑脱。
6. For consequent slope, when dip angle of structure plane is small, the mainly failure mode is slippage;
   当结构面倾角较小时，顺倾向层状边坡主要发生滑移破坏；
7. The clutch smoothly engage a spinning engine to a non-spinning transmission by controlling the slippage between them.
   离合器借助相互之间的打滑，使转动的发动机与静止的传动系平稳接合。
8. Application of Friction Pile to Control Side Slope Slippage at UHV Jingmen Substation
   抗滑桩在特高压荆门变电站边坡滑移治理中的应用
9. Every advance was followed by slippage and obstruction before, at long last, the job was done.
   光滑的路面和各种障碍使整个工作困难重重，最终，总算把工作做完了。
10. This paper analyzes the kinematical modeling of six? wheel lunar rover under the constraint of slippage.
    现对滑移条件下的六轮月球探测车进行了运动学建模与分析。
11. The Influence Research on Mechanical Property of Lighter Timber Truss Because of Truss Plate Slippage
    齿板滑移对轻型木桁架力学性能影响的研究
12. Incorrect use can lead to condom slippage or breakage
    不正确的使用会导致安全套滑脱或破裂
13. This clever software reduces the engine power to a point where the transmission slippage is controlled.
    这一智能软件会将引擎功率减小到打滑的变送器可控制的范围内。
14. They are unmatched for high starting loads and sustained slippage where heat generated tends to lower efficiency and shorten the operating life of conventional clutches.
    他们是无与伦比的，起点高负荷和持续的滑动时产生的热量会降低效率，缩短了运行寿命的常规离合器。
15. Many shoe stores recommend Lock Lacing techniques to help prevent slippage, and many people swear by them.
    许多鞋商店建议锁花边技术，以帮助防止滑动，许多人发誓他们。
16. Considering the slippage of the steel-concrete interface, this thesis simulates and analyses the deformation and receiving power capability of composite beam under the stage of elasticity;
    本文模拟分析了弹性工作阶段组合梁考虑界面滑移时的变形以及受力性能；
17. All three have to varying degrees cited exposure of Cypriot banks to Greece, but have also voiced misgivings about fiscal slippage.
    这三个国家都不同程度地引用了塞浦路斯希腊银行接触，但也有人对财政延误疑虑。
18. Pump actual work process, their internal leakage there is, also known as slippage.
    泵实际工作过程中，其内部存在泄漏，也称滑移量。
19. You can compare an interim plan with the baseline plan or current plan to monitor project progress or slippage.
    可以将中期计划与比较基准计划或当前计划进行比较，以监视项目的进度或进度落后情况。
20. Therefore, improvement of anti-thread gluing capability by the systems control is the only way to improve the thread joint performance, and reduce the screw thread slippage and seal failure.
    因此，系统控制，提高螺纹抗粘扣能力是改善螺纹联接性能，减少螺纹滑脱和密封失效的必由之路。
21. Layered Slippage of Stay Cables Shearing and Its Influence on Bending Stress
    斜拉索剪切分层滑移及其对弯曲应力的影响
22. We all know the sad story of our slippage in mathematics and science.
    我们都知道一个可悲的事实：我们的数学和科学水平下降了。
23. Deformable bearings that t ransmit seismic loads limited by plastic deformations or restricted slippage of bearing components;
    传递受到塑性变形或支座构件受限滑移限制的地震荷载的可变形支座；
24. TCS is equipped to prevent the slippage of the wheels on the snowy ground or slippery roads.
    循迹控制系统用来预防车轮在雪地及湿滑的道路上打滑。
25. When work rolls become worn the roughness is diminishing creating slippage in the roll bite at higher speeds.
    工作辊磨损后，粗糙度递减导致在较高轧制速度下进料（咬入带卷）时产生滑移。
26. Based on the statistics, 86% of tubing failure occurs in the place of thread joint, the failures of thread joint have two aspects, seal failure and slippage failure.
    据统计，油管失效86%发生在螺纹联接处，而螺纹联接失效表现在两个方面：密封失效和滑脱失效。
27. The mechanical contribution to this coupling is subject to the hysteresis, metallurgical instability, creep, and slippage at holding clamps.
    引起这种耦合的机械因素是由于滞后、金相不稳定性、蠕变和夹以部分的滑移等效应的影响。
28. Another consideration is slippage, which might occur at a clamp or joint.
    另外一个要考虑的问题是滑移。滑移可能产生于夹紧或联结处。
29. The reasons caused seal and slippage failure are complicated, the most important factor was the thread gluing reduced the intensity and the sealing property of the thread joint.
    造成密封和滑脱失效的原因较为复杂，最重要的因素是螺纹粘扣降低了螺纹联接的强度和密封性能。